GE
-
GE IC693ALG222 INPUT MODULE ANALOG 16 CHANNEL NEW
GE IC693ALG222 INPUT MODULE ANALOG 16 CHANNEL NEW
-
GE IC693ACC301
GE IC693ACC301
-
GE IC670PBI001
GE IC670PBI001
-
GE IC670ALG320 ANALOG OUTPUT MODULE CURRENT/VOLTAGE-SOURCE 4POINT NEW
GE IC670ALG320 ANALOG OUTPUT MODULE CURRENT/VOLTAGE-SOURCE 4POINT NEW
-
GE 469-P1-HI-A20-E
GE 469-P1-HI-A20-E
-
Manufacturer GE Analog Module IC693ALG392
IC693ALG392 is an Analog Current/Voltage Output Module for the PACSystems RX3i and Series 90-30. The module has eight single-ended output channels with voltage outputs and/or current loop outputs based on installation by the user. Each channel can be generated the configuration software for the subsequent scopes (0 to +10 volts) as unipolar, (-10 to +10 volts) bipolar, 0 to 20 milliamps, or 4 to 20 milliamps. Each of the channels is able to translate 15 to 16 bits. This is reliant on the range that is preferred by the user. All eight channels are renewed every 8 milliseconds.
-
Manufacturer GE CPU Module IC693CPU363
The GE Fanuc IC693CPU363 is a Module of GE Fanuc series 90-30 PLC systems. It connects to one of the CPU slots on a baseplate. This CPU is of type 80386X and has a speed of 25Mz. It gives the baseplate the ability to connect to up to seven remote or expansion baseplates. The power required for it to work is +5VDC and 890mA current. It has a battery to back up a clock and can be overridden. When it operates, its temperature can vary from 0 to 60 degrees in ambient mode.
-
Manufacturer GE CPU Module IC695CPU320
The IC695CPU320 is a Central Processing Unit from the GE Fanuc PACSystems RX3i Series. The IC695CPU320 has an Intel Celeron-M microprocessor rated for 1 GHz, with 64 MB of user (random access) memory and 64 MB of flash (storage) memory. RX3i CPUs are programmed and configured to control machines, processes, and material handling systems in real time.
-
Manufacturer GE Iput Module HE693RTD601
The HE693RTD601 allows RTD temperature sensors to be connected to the PLC directly without external signal processing such as transducers, transmitters, etc. All analog and digital processing on the module is performed on the HE693RTD601, and temperature values in 0.5°C or 0.5°F increments are written to the 90-30 %AI input table.
-
Manufacturer GE Module IC693ALG222
The number of channels in the IC693ALG222 may be single ended (1 to 16 channel) or differential (1 to 8 channel). The power requirement for this module is 112mA from 5V bus, and also it requires 41V from 24V DC supply to power the converters. The two LED indicators indicate the status of user power supply the module’ status. These two LEDs are MODULE OK, which gives the status regarding power-up, and POWER SUPPLY OK, which checks whether the supply is above the minimum required level. The IC693ALG222 module is configured either using logic master programming software or via Handheld programming. If the user chooses to program the module via Handheld programming, he can only edit active channels, not active scanned channels. This module uses the %AI data table to record analog signals for the use of the programmable logic controller.
-
Manufacturer GE Module IC693PWR321
The GE Fanuc IC693PWR321 is a standard power supply. This unit is a 30 watt supply that can use direct or alternating current. It operates on an input voltage of either 120/240 VAC or 125 VDC. Aside from a +5VDC output, this power supply can provide two +24 VDC outputs. One is a relay power output, which is used to power circuits on Series 90-30 Output Relay modules. The other is an isolated output, which is used internally by some modules. It can also provide external power for 24 VDC Input modules.
-
Manufacturer GE Output Module IC693MDL730
The GE Fanuc IC693MDL730 is a 12/24 Volt DC Positive Logic 2 Amp Output module. This device is designed to work with the Series 90-30 Programmable Logic Controller. It provides 8 output points in a single group, which share a common power input terminal. The module has positive logic characteristics. This is evident in the fact that it provides current to the loads, sourcing it from the positive power bus or else the user common. Users who want to operate this module can do so with a range of output devices, including indicators, solenoids and motor starters. The output device must be connected between the module output and the negative power bus. The user needs to set up an external power supply to provide the power needed to operate these field devices.
